Super Ezy Bond

Description:

Cemix® Super Ezybond is cement based economical adhesive for interior or exterior fixing of tiles on rigid concrete surfaces by professionals. Cemix® Super Ezybond is cement based rigid set, exceptionally high strength, high quality adhesive ideal for bonding most types of ceramic tiles, porcelain, mosaic, natural stone, marble and granite for wall and floor applications onto rigid substrates. Suitable for both thick and thin bed applications. When using Cemix® Super Ezybond with translucent/absorbent/ moisture sensitive tiles and stone, the colour of the adhesive must be considered, to avoid discolouration problems. When fixing over flexible substrates i.e., fibrous cement sheeting, plasterboard etc. mix Cemix® Super Ezybond with Cemix® Cemlastic as a total water replacement to produce improved adhesion, flexural and compressive strength. A mix of Cemix® Super Ezybond and Cemix® Cemlastic should also be used on more difficult surfaces including those in fully immersed situations or high point loads etc. Please contact cemix technical support for more details for large commercial applications.

Typical Application / Uses:

  • For bonding most types of ceramic tiles, porcelain, mosaic, natural stone, marble and granite for wall and floor applications onto rigid substrates

Advantages:

  • High strength
  • High quality adhesive
  • Suitable for both thick and thin bed applications
  • Can be used to apply onto rigid substrates.

20kg

Substrate Preparation:

The substrate should be free of dust, grease, wax, oil, dirt, loose plaster, laitance, curing compounds, paint and all other friable materials and contaminants likely to prevent the adhesive bonding. New concrete should be left with a wood float finish and sufficiently aged for a minimum of 28 days. Shiny smooth surfaces on old concrete should be acid etched or scabbled. Cemix® cement screeds/floor levelers must be allowed to cure for a minimum of 7 days. All substrates should be securely fastened and properly supported to eliminate any movement that may cause cracking. Refer to the substrate test guide below for recommended surface preparation. To achieve warranted performance, it is recommended that all substrates should be primed with Cemix® Cemlastic with a brush/roller undiluted from the container. Allow to become tacky before tiling. For further information, contact the Cemix® Technical support.

Perform the substrate test:

No water absorbed: Mechanically prepare substrate.

Moderate water absorbed: Clean with damp sponge and water.

All water absorbed: Broom on liberal amounts of water.

This simple test is performed after vacuuming or sweeping a number of test areas and applying a single drop of fresh drinking water from the end of your finger. This should be approximately 20mm wide when it first hits the floor – if it beads and remains whole then “No water is absorbed”. If it loses all gloss within 20 - 60 seconds then “Moderate water is absorbed”. If the gloss disappears instantly or within 20 seconds then the substrate has “All water absorbed”. Look for different surface appearance in your floor and test each to ensure your test is representative of the whole area. Perform test in both a cool shaded area and an exposed sunny area if tiling externally.

Movement / Control Joints:

Movement joints must be incorporated at the design stage and in accordance with

AS 3958.1-2007 as follows:

  1. Over movement joints in the background
  2. At a junction between different backgrounds materials
  3. At internal vertical corners and fixtures interrupting the tile surface e.g. columns
  4. Around the perimeter of the tiling area
  5. At a maximum of 5m intervals in a grid pattern. Consideration should be given to the provision of additional movement joints with large tiles, e.g. 400 x 400 plus, when exposed to strong sunlight.

Note: Movement joints should go right through the tile adhesive bed to the background and be kept free from dirt and adhesive droppings. Movement joints must not be less than 6mm or greater than 10mm wide. All movement joints that are 6mm wide can be filled with flexible sealant.

Mixing:

  1. Add approx. 5L of clean water to a bucket.
  2. Sprinkle Cemix® Super Ezybond slowly into the water, mixing constantly until a tick creamy toothpaste consistency is achieved – with no lumps.
  3. Allow to stand for 5 minutes and re mix and then the adhesive is ready to use.
  4. Use Cemix® Cemlastic as total water replacement in areas subject to movement, vibration, thermal fluctuation, expansion or contraction, immersed applications and when adhering to non-porous surfaces or tiles. In such situations please ensure that a minimum of 90% of adhesive contact is achieved to the back of the tiles. Do not aerate the mix by stirring over vigorously or for too long. The mix should be stiff enough to keep its shape when spread with a notched trowel.

Application:

All workmanship must be carried out in accordance with AS3958.1-2007.

Spread the adhesive evenly with a 6mm x 6mm notched trowel for tiles up to 150mm x 150mm and for larger tiles use a 12mm x 12mm notched trowel. Lay the tiles with a good pressure, twisting to ensure good contact with the adhesive. In more demanding exterior situations, or if tiles with high ribs or lugs are being used, it is preferable to spread the backs of the tiles with a thin layer of adhesive in addition to the adhesive being trowelled onto the substrate, before laying. Do not spread more than 1m2 of adhesive at any one time as skinning may occur affecting final adhesion. Press tiles onto the adhesive before it skins and ensure that the tiles are fully supported with the adhesive with no voids. Occasionally, in order to ensure that full coverage is being maintained, a tile should be removed, ensuring the adhesive coverage to be over 90% and the tile be re laid accordingly. Once the tiles have been laid, they must not be trafficked upon or disturbed for a minimum of 24 hours at 20oC.

Grouting:

Grouting may be undertaken after 24 hours but allow a further 24 hours before general use.

Technical Data:

Appearance – Grey Powder

Application Temp – 5 – 30oC

Yield / Coverage - Varies according to size from approximately: 6.6m2 per bag of 20Kg using 6 mm notched trowel 3.3m2 per bag of 20Kg using12mm notched trowel

Adjustment time at 18oC – 15 minutes

Pot life at 18oC – 1 hour

Classification – C1E (with water) CIES2 (with Cemix Cemlastic as a total water replacement).

Bulk Density – 1.50kg/litre

The data shown above reflects typical results based on laboratory testing under controlled conditions. Reasonable variations may occur on site.

Limitations:

  • Not suitable for tiling over flexible substrates, such as fibrous cement sheeting, plasterboard, particle board, MDF, plywood and timber. Also unsuitable for plastic, metals and existing tiles. Must be mixed with undiluted Cemix® Cemlastic for fully immersed areas and where high point loads, vibration, shrinkage or expansion may occur.
  • Recommended for use over Cemix® approved waterproofing membranes – only when mixed with undiluted Cemix® Cemlastic.
  • Not suitable for any impervious non absorbent surface unless mixed with undiluted Cemix® Cemlastic
  • Not suitable for moisture sensitive tiles stones or green marble as discolouration might occur. Brush apply the moisture sensitive stone with Cemix® Pavseal and then fix the sealed stone as
  • Normal after 4 - 5 hours – to avoid discolouration and moisture penetration.
  • Only to be used between 5oC and 30oC and avoid extreme windy locations.
  • External tiling must not to exceed 2.7m in height
  • Suspended concrete slabs must conform to AS/NZ3958.1-2007 for maximum deflection. Any post tensioned concrete slab must be treated as a flexible substrate and thus not suitable for Cemix® Super Rigid Set.

Storage:

Twelve (12) months - unopened bags in dry weatherproof storage.

Cleaning:

Remove excess adhesive from between the tiles and clean the tile faces with a damp sponge before the adhesive sets. Clean tools and adhesive with water before the adhesive dries

Precaution:

Being cement based, may cause respiratory, skin and eye irritation. Wet cement can be irritating and corrosive to eyes and skin; and may cause skin sensitization (dermatitis). Repeated inhalation may cause bronchitis, silicosis and lung cancer and increase risk of scleroderma.